|
|
|
Site Preparation
- The entire site perimeter will be inspected for items that may get damaged in the roofing process. These will be moved away from the work area.
- Tarps will be spread around the perimeter of the home and over the shrub beds to protect any plants and to collect falling debris.
- A dump trailer will be placed in a convenient spot to receive demolition and waste material.
Worker Safety
- Workers will place ladders at least three feet above the eave.
- Workers will wear appropriate protective clothing and shoes.
- Worker’s will fasten cleats at the eaves, put on safety harnesses and fasten the harness to the cleats with approved lanyards.
Demolition Phase
- Shingles and underlayment will be stripped in sections starting at the top and working down.
- The entire roof deck will be inspected for rotted or damaged wood. Unsuitable decking will be replaced with new material.
- The entire roof deck will be nailed to meet the current 2014 building codes.
- The soffit and fascia will be inspected. The owner will be notified if any repairs are required.
Roof Dry-in
- For general roofs, a woven synthetic underlayment will be used.
- For upgrade roofs, a self-adhering modified bitumen membrane will be installed at all eaves, valleys, penetrations and other leak prone areas.
- The woven synthetic underlayment will then be used in other areas, overlapping each horizontal run by three inches and each vertical seam by eighteen inches. The underlayment is fastened with plastic cap nails every one foot and within one inch of each edge.
- For a further upgrade, a heavier woven synthetic underlayment can be used.
- The drip edge will be cemented in place along the perimeter and fastened to the deck with roofing coil nails spaced four inched apart.
- All accessories, to include vent pipe boots, exhaust vents and pitch pockets will be installed.
Shingle installation
- The roof is shingled from the bottom up. Before the first shingle is installed, a starter strip will be placed at the eaves around the perimeter of the home. This strip has a factory-applied adhesive that glues the shingle to the roof. This starter strip provides for a 130 mph wind resistance vs. 110 mph for a standard starter shingle.
- The shingles will then be installed. Each shingle has an adhesive built in which adheres it to the shingle below. All shingles ate fastened with six nails per the 2014 building code.
- At the end of the shingle installation, a special ridge cap shingle will be used. This is superior to standard cut 3-tab shingle caps in that they perfectly match the field shingles and that they provide the 10mph wind rating.
Ventilation
- A ventilation calculation will be done to determine the extent of attic ventilation required. It is important to properly exhaust heat and moisture from the attic in order to keep the home cool and further the life of the roof.
- A continuous polymer ridge vent will be installed in appropriate areas. The continuous ventilation has no metal components and fasteners are not exposed to prevent corrosion.
- Off ridge vents may be used in certain circumstances.
Completion
- After all of the shingles have been installed, the loose granules will be blown off of the roof. Gutters will be cleaned and the tarps will be collected. The grounds will be magnetically swept for nails and other bits of metal.
- The dump trailer will be removed from the property.
Inspections
Two inspections by the local building department will take place:
1) an in-progress inspection, to check the deck and the underlayment installation, and 2) a final inspection to check the shingle and accessory installation.
|
Maybe you’re not quite sure where to start? Or maybe you have re-roofed your home before.
|
Have you experienced damage to your roof from a storm or normal wear and tear? We offer emergency roof repair services to our customers including tarping services and insurance assistance.
|
We recommend annual inspections (as a minimum) for every roof system. Far too often, the cause of a roof failure is the absence of proper maintenance and inspection.
 |
|
|---|---|
| Leakage in Attic After Wind-Driven Rain | |
| Possible cause: Leaky or inadequate shingle underlayment or deteriorated flashing |  |
| Leakage in Attic After Ice Build-Up | |
| Possible cause: Inadequate shingle underlayment allows water from ice dams to leak into attic |  |
| Blistering and/or peeling of interior and/or exterior paint | |
| Possible cause: Excessive temperature or high humidity due to poor attic ventilation |  |
| Stains on Interior Ceilings and Walls or Mold and Mildew Growth | |
| Possible cause: Inadequate or faulty shingle underlayment allowing leakage or inadequate ventilation |  |
| Exterior Decay, Sheathing, and/or Siding | |
| Possible cause: Poor attic ventilation |  |
| Missing, Cracked or Curled Shingles | |
| Possible cause: Shingles have reached the end of their useful life |  |
| Dark, "Dirty-Looking" Areas On Your Roof | |
| Possible cause: Environmental pollutants; vegetation, fungus or algae; loss of granules due to age of shingles |  |
| Excessive Energy Costs | |
| Possible cause: Insufficient attic ventilation causes heating/cooling system to run excessively In warm weather, inadequate ventilation will trap hot air in the attic, causing air conditioning systems to work harder, or leaving your home's interior hotter and less comfortable. Attic Ventilation: In both hot and cold weather, insufficient attic ventilation may cause moisture in the attic to become trapped and condense on the rafters. This condensed moisture can drip down onto the insulation and reduce its effectiveness. Excessive energy costs can result. |
 |
Roofing Terms
A
Algae- Rooftop fungus that can leave dark stains on roofing.
Angled fasteners- Roofing nails and staples driven into decks at angles not parallel to the deck.
APA- American Plywood Association. Tests and sets standards for all varieties of plywoods used in the U.S.
Apron flashing- Metal flashing used at chimney fronts.
ARMA- Asphalt Roofing Manufacturer’s Association. Organization of roofing manufacturers.
Asphalt- A bituminous waterproofing agent used in various types of roofing materials.
Asphalt concrete primer- Asphalt based primer used to prepare concrete and metal for asphalt sealant.
Asphalt plastic cement- Asphalt based sealant material, meeting ASTM D4586 Type I or II. Used to seal and adhere roofing materials. Also called mastic, blackjack, roof tar, bull.
ASTM-The American Society for Testing and Materials. Organization that sets standards for a wide variety of materials, including roofing.
B
Back-surfacing- Granular material added to shingle’s back to assist in keeping separate during delivery and storage.
Blistering- Bubbles or pimples in roofing materials. Usually moisture related. In shingles blisters are either moisture under the material or moisture trapped inside the material.
Blow-offs- When shingles are subjected to high winds, and are forced off a roof deck.
Buckling- When a wrinkle or ripple affects shingles or their underlayments.
C
Closed-cut valley- A shingle valley installation method where one roof plane’s shingles completely cover the other’s. The top layer is cut to match the valley lines.
Cobra®- GAFMC’s respected brand name for ventilation products.
Corrosion- When rust, rot or age negatively affect roofing metals.
Counter-flashing-The metal or siding material that is installed over roof-top base flashing systems.
Country Mansion® & Country Estates™-GAFMC’s limited lifetime warranty shingle.
Crickets- A peaked water diverter installed behind chimneys and other large roof projections. Effectively diverts water around projections.
Cupping- When shingles are improperly installed over an existing roof or are over-exposed, they form a curl or cup.
D
Deck- The substrate over which roofing is applied. Usually plywood, wood boards, or planks.
Dormer- A raised roof extending out of a larger roof plane.
Drip-edge- An installed lip that keeps shingles up off of the deck at edges, and extends shingles out over eaves and gutters, and prevents water from backing up under shingles.
Dubl-Coverage® Mineral Guard- Roll roofing material with 19" selvage edge for double coverage over roof deck.
E
Eaves- The roof edge from the fascia to the structure’s outside wall. In general terms, the first three feet across a roof is termed the eave.
End-laps- When installing rolled products in roofing, the area where a roll ends on a roof, and is overlapped by the next section of rolled material. (underlayments, rolled roofing)
Exposure- The area on any roofing material that is left exposed to the elements.
F
Fasteners- Nails or staples used in securing roofing to the deck.
FHA-The Federal Housing Authority. Sets construction standards throughout the U.S.
Fiberglass mat- fibers condensed into strong, resilient mats for use in roofing materials.
Flange-Metal pan extending up or down a roof slope around flashing pieces. Usually at chimneys and plumbing vents
Flashing- Materials used to waterproof a roof around any projections through the roof deck.
Flashing cement- Sealant designed for use around flashing areas, typically thicker than plastic cement.
G
Gable roof- Traditional roof style; two peaked roof planes meeting at a ridge line of equal size.
GAFCant®- GAFMC cant strips for deflecting water away from flashing areas. Typically used on low slope roofs.
Golden Pledge®- GAFMC’s strongest limited warranty for shingles. America’s strongest steep slope warranty.
Grand Sequoia®- GAFMC shingle with wood shake appearance.
Grand Slate™- GAFMC shingle with slate appearance.
Granules- Crushed rock that is coated with a ceramic coating and fired, used as top surface on shingles.
H
Hand-sealing- The method to assure sealing of shingles on very steep slopes, in high wind areas, and when installing in cold weather.
High nailing- When shingles are nailed or fastened above the manufacturer’s specified nail location.
Hip legs- The down-slope ridges on hip roofs.
Hip roof- A roof with four roof planes coming together at a peak and four separate hip legs.
I
Ice Dam- When a snow load melts on a roof and re-freezes at the eave areas. Ice dams force water to "back-up" a roof and cause leakage.
L
"L" flashing- Continuous metal flashing consisting of several feet of metal. Used at horizontal walls, bent to resemble an "L".
Laminated shingles- Shingles made from two separate pieces that are laminated together. GAFMC Timberline® Series, Country Mansion® and Grand Sequoia® Shingles. Also called dimensional shingles and architectural shingles.
Laps- The area where roll roofing or rolled underlayments overlap one another during application (see also side laps and end laps).
Low slopes-Roof pitches less than 4/12 are considered low sloped roofs. Special installation practices must be used on roofs sloped 2/12-4/12.
M
Mansard- A roof design with a nearly vertical roof plane that ties into a roof plane of less slope at its peak.
Mats- The general term for the base material of shingles and certain rolled products.
Modified bitumen- Rolled roofing membrane with polymer modified asphalt and either polyester or fiberglass reinforcement.
Mortar- Mixture of sand, mortar, limestone and water used in bonding a chimney’s bricks together.
N
Nail-guide-line- Painted line on laminated shingles, to aid in the proper placement of fasteners.
Nail-pop- When a nail is not fully driven, it sits up off the roof deck.
Nesting- Installing a second layer of shingles aligning courses with the original roof to avoid shingle cupping.
NRCA- The National Roofing Contractors Association. Respected national organization of roofing contractors.
O
Open valley- Valley installation using metal down the valley center.
Organic mat- Material made from recycled wood pulp and paper.
Organic Shingles- Shingles made from organic (paper) mats.
OSB- Oriented Strand Board. A decking made from wood chips and lamination glues.
Over-driven- The term used for fasteners driven through roofing material with too much force, breaking the material.
Over-exposed- Installing shingle courses higher than their intended exposure.
P
Pitch-ratio of the rise of the roof to the span of the roof.
Power vents- Electrically powered fans used to move air from attics and structures.
Plastic cement- Asphalt based sealant. Also called bull, mastic, tar, asphalt cement.
Plumbing vents- Term used to describe plumbing pipes that project through a roof plane. Also called vent stacks.
Prevailing wind- The most common direction of wind for a particular region.
Q
Quarter sized- Term for the size of hand sealant dabs, size of a U.S. 25¢ piece.
R
Racking- Method of installing shingles in a straight up the roof manner.
Rake edge-The vertical edge of gable style roof planes.
Release film- The plastic sheet installed on the back of Weather Watch® and StormGuard® underlayments. Used for packaging and handling. Remove before installation.
Rigid vent- Hard plastic ridge vent material.
Roof louvers- Rooftop rectangular shaped roof vents. Also called box vents, mushroom vents, airhawks, soldier vents.
Roof plane- A roofing area defined by having four separate edges. One side of a gable, hip or mansard roof.
S
Sawteeth- The exposed section of double thickness on Timberline® Series shingles. Shaped to imitate wood shake look on the roof.
Self-sealant- Sealant installed on shingles. After installation, heat and sun will activate sealant to seal the shingles to each other.
Selvage- The non exposed area on rolled roofing. Area without granules. Designed for nail placement and sealant.
Shed roof- Roof design of a single roof plane. Area does not tie into any other roofs.
Shingle-Mate®- GAFMC’s shingle underlayment. Breather type with fiberglass backing to reduce wrinkles and buckles.
Side-laps- The area on rolled material where one roll overlaps the rolled material beneath it. Also called selvage edge on rolled roofing.
Side-walls- Where a vertical roof plane meets a vertical wall. The sides of dormers etc.
Soffit ventilation- Intake ventilation installed under the eaves, or at the roof edge.
Smart Choice® Limited Warranty- GAFMC’s standard shingle limited warranty.
Smart Choice® System Plus Limited Warranty- GAFMC’s next grade of enhanced warranty. Extended coverage for owners.
Starter strip- The first course of roofing installed. Usually trimmed from main roof material.
Steep slope roofing- Generally all slopes higher than 4/12 are considered steep slopes.
Step-flashing- Metal flashing pieces installed at side-walls and chimneys for weather-proofing.
StormGuard®- GAFMC waterproof underlayment. Film surfaced rolled underlayment, 1.5 squares coverage per roll.
T
Tab- The bottom portion of traditional shingle separated by the shingle cut-outs.
Tear-off- Removal of existing roofing materials down to the roof deck.
Telegraphing- When shingles reflect the uneven surface beneath them. Shingles installed over buckled shingles may show some buckles.
Timberline® Series- GAFMC’s trademark name for laminated wood shake style shingles.
TIMBERTEX®- GAFMC enhanced Hip and Ridge Shingles.
Transitions- When a roof plane ties into another roof plane that has a different pitch or slope.
U
Under-driven- Term used to describe a fastener not fully driven flush to the shingles surface.
Underlayments- Asphalt based rolled materials designed to be installed under main roofing material, to serve as added protection.
V
Valleys-Area where two adjoining sloped roof planes intersect on a roof creating a "V" shaped depression.
Vapor- Term used to describe moisture laden air.
Ventilation- The term used in roofing for the passage of air from an enclosed space.
W
Warm wall- The finished wall inside of a structure, used in roofing to determine how to install waterproof underlayments at eaves.
Warranty- The written promise to the owner of roofing materials for material related problems.
Waterproof underlayments- Modified bitumen based roofing underlayments. Designed to seal to wood decks and waterproof critical leak areas.
Weather Stopper® Integrated Roofing System™- GAFMC’s complete roofing system and components.
Weather Watch®- GAFMC’s granule surfaced waterproof underlayment.
Woven Valleys- The method of installing valleys by laying one shingle over the other up the valley center.
|
